Tool bag proof
Off the floor and ready to work
The clip shows the loaded bag on the open stand, then moves closer to the attached frame and tools.
Tools & trade
The tool bag stand for the job site.
The Ryzer Go clamps to the bottom of your tool bag and lifts it 13.7 inches off the ground. Your tools stay out of the mud, off the wet slab, and at reach while you work. HVAC, electrical, plumbing, field service, it holds up to 50 pounds of whatever you carry.
tools at reach, not underfoot.
50 lb
max bag weight
What is the Ryzer Go for tool bags?
It is a lightweight stand that clamps to the bottom of a tool bag, tote, or tool backpack. Twist the handle and spring-loaded legs pop out to hold the bag upright, 13.7 inches off the ground. It carries bags up to 50 pounds and weighs about 2.4 lb. Carry it open in landing mode, or manually fold the legs flat for the truck, storage, and tight spaces.
Holds tool bags up to 50 pounds
Lifts the bag 13.7 inches off the slab
Fits open-top totes, gatemouth bags, and tool backpacks
Carry open in landing mode. Manually folds flat for the truck
See it on the job
Watch setup videos A loaded tool bag, standing on its own.
Watch the Ryzer Go hold a working tool bag upright with the frame, legs, and bag all clearly visible.
On the clock
Why tradesmen put their bag on a Ryzer.
Job sites are hard on gear. Floors are wet, dusty, or torn up, and the bag goes down wherever the work is. The Ryzer Go keeps your tool bag upright, elevated, and at hand so you spend less time bent over the floor digging for a driver.
Wet
Off the slab
Mechanical rooms, crawl spaces, fresh concrete, gravel. Your bag stays 13.7 inches above all of it, and so do your tools.
50 lb
Built for real loads
The recommended maximum bag weight is 50 pounds. Weigh the loaded bag if you are unsure, and choose a firm, stable placement before opening it.
Reach
Tools at hand
The bag sits upright where you can see into it, with tools easier to reach throughout the job.
Twist to deploy
How the Ryzer Go works on the job.
Attach it to your bag once. Carry it open in landing mode, or manually fold the legs flat for the truck, storage, and tight spaces.
1
Attach it once
Clamp the Ryzer Go to the bottom of your tool bag. The mounting pins create tiny pin holes and hold only the stand's own weight.
2
Twist to deploy
A quick twist pops the spring-loaded legs open. Your bag is upright in seconds, no hands needed to hold it.
3
Work out of it
The bag sits upright with every pocket at reach. Choose a firm, stable placement before opening it.
4
Carry open or fold flat
Carry it open in landing mode, or manually fold both legs flat for the truck, storage, or tight spaces.
Build out your rig.
Extra attachment sets to move the Ryzer Go between bags, MOLLE hooks, grip strips, and more.
The numbers
Specs for the Ryzer Go.
13.7″
Lift off the ground
2.4 lb
Weight
7″ / 9″
Depth sizes
50 lb
Max bag weight
10–16″
Bag width it fits
5.5–12″
Bag depth across both sizes
Folds flat
Packs against the bag
Polymer + aluminum
Stainless steel hardware, padded back
Will it fit your bag?
What size do I need for a tool bag?
Measure the loaded bag front to back at the base. Choose the depth that contains that measurement. Bag style does not decide it.
7-inch depth
For loaded bags 5.5″ to 9.5″ deep
Choose this depth when the loaded bag's base falls in this range. Bag type does not decide the depth.
9-inch depth
For loaded bags 8.5″ to 12″ deep
Choose this depth by measurement. Bags from 8.5 to 9.5 inches deep can use either option.
Tool bag questions
Tool bag stand FAQ.
How do I keep my tool bag off the ground?
Attach the Ryzer Go to the bottom of the bag. A quick twist pops out spring-loaded legs that hold the bag upright, 13.7 inches off wet or dirty floors, so your tools stay clean and at reach.
Will it hold a fully loaded tool bag?
The recommended maximum bag weight is 50 pounds. Weigh the loaded bag if you are unsure, and choose a firm, stable placement before opening it.
Does the Ryzer Go fit tool backpacks and open-top totes?
It fits most of them. The stand clamps to bags 10 to 16 inches wide, and the two depth sizes cover bags from 5.5 to 12 inches deep at the base. Measure your bag loaded and pick the depth that covers your number.
Will it slow me down moving between jobs?
No. Carry it open in landing mode, or manually fold the legs flat against the bag for the truck, storage, and tight spaces. The stand stays attached and adds about 2.4 pounds.
What marks do the clamps leave?
The clamp mounting pins create tiny pin holes and hold only the stand's own weight of about 2.4 pounds. You can also move it between bags with an extra attachment set.
How much is the Ryzer Go and when does it ship?
The Ryzer Go website pre-order price is $79.99. Website pre-orders are expected to ship in early October 2026. Shipping is calculated at checkout.
Pre-order now live
Get your tools off the floor.
Reserve the Ryzer Go at $79.99. Website pre-orders are expected to ship early October 2026.
Fully funded on Kickstarter in 2 hours · 1,200+ backers